Tyco Power832 Security System PC5016 Manuel d'utilisateur télécharger pdf (Page 7)

Programming codes from an LCD Keypad:

Master Code

Press the [

✱] key to enter the function list. Scroll (< >) to...

Press [5] or [

✱]. The display will read...

Enter your current Master Code. The display will read...

“01P” represents the first access code. Use the arrow (< >) keys to scroll to “40P”

and press the [

✱] key to indicate that you wish to program the Master Code. The

display will read...

Enter the new Master Code. The Master Code must be four digits unless otherwise

indicated by your installer. Enter digits 0 through 9 only. Once the new code is

entered, the keypad will beep 3 times and the display will read...

Press [#] to exit the code programming function.

Be sure to record your new Master Code on the “System Information” page in this booklet. NOTE: We

recommend that the factory default Master Code [1234] not be used.

Additional Access Codes

To erase, add or change a user code, press [

✱] to enter the functions list. Use the arrow (< >) keys to

scroll to the following message...

Press [✱]. Display will read...

Enter the Master Code. Display will read...

Use the scroll keys (< >) to find the access code – indicated by “01P” to “32P” –

you wish to add, change or delete. Press the [

✱] key to select the code you wish to

alter. The display will read...

To add or change a code, enter the new code. Access codes must be four digits

unless otherwise indicated by your installer. Enter digits 0 through 9 only. To delete

an access code, enter [

✱]. Once the 4 digit code or [✱] has been entered, the

keypad sounder will beep 3 times and the display will read...

The “P” means the code has been programmed. If there is no “P” then that code is

deleted. Press [#] to exit the code programming function. Do not erase the Master code.

Remember to record your new code(s) on the “System Information” page in this booklet.

Access Code Attributes

Additional programmable attributes, such as zone bypassing capability, can be activated or

deactivated for each access code. For more information regarding access code attributes, please

contact your installer.

Press (*) for < >

Access Codes

Enter Master

Access Code

[*] to Edit <>

User Code 01P

Enter New Code

1234 < >

[*] to Edit <>

User Code 01P

(*) to Edit < >

User Code 01P

Enter Master

Access Code

(*) to Edit < >

User Code 01P

Enter New Code

1234 < >

Press (*) for < >

Access Codes

If An Alarm Sounds

Fire Alarm

If your system has been installed with fire detectors and the alarm sounds in a pulsing mode, follow

your emergency evacuation plan immediately (see “Fire Escape Planning” on page 15).

Intrusion Alarm

If an intrusion alarm sounds, indicated by a continuous bell or siren, the alarm may be silenced by

entering your access code. If the alarm was unintentional, call local authorities immediately to avoid an

unnecessary response.

You can determine the source of the alarm by following the instructions in the “Disarming” section (see

page 6). Once the source of the alarm has been corrected, the panel can be restored to its original

Armed state.

Function Keys

Each keypad has five function keys, located to the right of the number pad, which allow easy single-

button activation of the most commonly used features.

If these keys have been enabled by your

installer

, you can execute their programmed function by pressing and holding the corresponding key

for two seconds.

For information regarding the operation of the function keys, talk to your alarm installer.

Programming Security Codes

Programming codes from an LED Keypad:

The Master Code

To program the Master Code, enter [

✱][5][current Master Code][40][new Master Code]. The Master

Code must be four digits unless otherwise indicated by your installer. Enter digits 0 through 9 only.

Press [#] to return to the Ready state.

Be sure to record your new Master Code on the “System Information” page in this booklet. NOTE: We

recommend that the factory default Master Code [1234] not be used.

Additional Codes

Up to 32 additional access codes (01 through 32) may be programmed.

To program a new code:

Enter [

✱][5][Master Code][code number 01 to 32][new access code]. The code number is a double digit

from 01 to 32. Access codes must be four digits unless otherwise indicated by your installer. Enter

digits 0 through 9 only. Press [#] to return to the Ready state.

If an access code already exists for the code number you have selected, it will be replaced by the new

code. Be sure to record your new code(s) on the “System Information” page in this book.

To erase a code:

Enter [

✱][5][Master Code][code number 01 to 32][✱]. Press [#] to return to the Ready state. Do not

erase the Master code.

Continued on page 10...

1 2 3 4 5 6 7 8 9 10

Commentaires sur ces manuels

Pas de commentaire

Tyco Power832 Security System PC5016 Manuel d'utilisateur Page 7

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel Tyco Power832 Security System PC5016